EN-Engineering-Product-Ymagine Direct-rolled-Structural steel-Ymagine S1-Properties TSN
Mechanical properties
The mechanical properties are measured transverse to the rolling direction:
|
Relationship with European standard |
ReH / Rp |
Rm |
A80 |
Adp5 |
|---|---|---|---|---|
|
EN 10025-2: 2004, S235JR |
N/mm² |
N/mm² |
% |
% |
|
t < 3 |
t ≥ 3 |
|||
|
Hot-rolled flat products |
≥ 235 |
360 - 510 |
≥ 17 |
≥ 24 |
|
Ymagine S1 |
Rp |
Rm |
A80 |
Adp5 |
|---|---|---|---|---|
|
|
N/mm² |
N/mm² |
% |
% |
|
t < 3 |
t ≥ 3 |
|||
|
Typical value |
300 |
395 |
28 |
- |
|
Guaranteed values |
235 - 360 |
360 - 510 |
≥ 19 |
24 |
Chemical composition
Cast analysis in weight percentages:
|
Ymagine S1 |
C |
Mn |
P |
S |
Si 1 |
|---|---|---|---|---|---|
|
Typical |
0.045 |
0.220 |
0.008 |
0.007 |
0.018 |
|
Guaranteed (max) |
0.065 |
0.300 |
0.025 |
0.015 |
0.035 |
1. For the purpose of batch galvanising, Ymagine S1 can be ordered on consultation with a maximum Si content of 0.030%.
EN-Engineering-Product-Direct-rolled-Structural steel-Ymagine S1-Dimensions TSN
Dimensions
Dimensions in mm.
|
Thickness |
Ymagine S1 |
|
|---|---|---|
|
from - up to |
Minimum width |
Maximum width |
|
1.15 - 4.00 |
1000 |
1530 |
EN-EngineeringAutomotive-Product-Ymagine Direct-rolled-All grades Shape and dimensional tolerancesTSN
Shape and dimensional tolerances
Tolerances on thickness
Ymagine is available with the following tolerances.
Dimensions in mm:
|
Thickness |
Tolerances |
|---|---|
|
1.15 ≤ t ≤ 2.0 |
± 0.05 |
|
2.0 < t ≤ 2.5 |
± 0.06 1 |
|
2.5 < t ≤ 3.0 |
± 0.07 2 |
|
3.0 < t ≤ 4.0 |
± 0.09 3 |
1. In some instances, the material will be supplied with a tolerance of -0.06/+0.15 mm,
only on the coil head and tail and to a maximum of 20 metres from the start of the coil.
2. In some instances, the material will be supplied with a tolerance of -0.07/+0.17 mm,
only on the coil head and tail and to a maximum of 20 metres from the start of the coil.
3. In some instances, the material will be supplied with a tolerance of -0.09/+0.21 mm,
only on the coil head and tail and to a maximum of 20 metres from the start of the coil.
Tolerances on width
Width tolerances comply with standard EN 10051: 2010 (hot-rolled) and
EN 10131: 2006 (cold-rolled). Closer tolerances are possible – please contact us for details.
Width tolerances for Hot-rolled products
Tolerances in mm.
| Nominal width w | ||||
|---|---|---|---|---|
| Mill edges | Trimmed edges | |||
| lower | upper | lower | upper | |
|
w ≤ 1200 |
0 |
20 |
0 |
3 |
|
1200 < w ≤ 1850 |
0 |
20 |
0 |
5 |
|
w > 1850 |
0 |
25 |
0 |
6 |
Width tolerances for Cold-rolled products
Tolerances in mm.
|
Nominal width w |
Normal tolerances |
Special tolerances (S) |
||
|---|---|---|---|---|
|
Under |
Over |
Under |
Over |
|
|
w ≤ 1200 |
0 |
4 |
0 |
2 |
|
1200 < w ≤ 1500 |
0 |
5 |
0 |
2 |
|
w > 1500 |
0 |
6 |
0 |
3 |
Special width tolerances may be available (± 0.50 mm available on 750 - 2000 mm width). Please contact us for details.
Dimensions and coil weights
The weight of weld-free coils can be specified freely between 13 and 20.5 kg/mm.
Ymagine is supplied with trimmed edges as standard. Mill edges are available on request.
|
Description |
Dimension or weight |
|---|---|
|
Outside diameter |
minimum 1050 mm maximum 2000 mm (Ymagine) maximum 2100 mm (mill scale) |
|
Coil Weight |
maximum 31.5 tonne 1 |
1. For Ymagine H500 the maximum coil weight is 25 tonne for thicknesses > 2.5 mm.
Above 3.20 mm maximum coil weight for all grades is 25 tonne. Higher coil weights available on request.
Tata Steel assumes a minimum and a maximum coil weight agreed upon with the customer on the basis of our normal production practices and an order quantity corresponding to this coil weight. Usually a minimum coil weight up to 90% of the maximum coil weight can be requested.
Surface aspects
The surface quality of Ymagine is comparable to hot-rolled pickled and oiled i.e. 1 - 3 μm Ra (cut off 2.5mm).
Ymagine is suitable for cold-rolled applications that are not surface-critical.
EN-EngineeringAutomotive-Product-Hot-rolled-Heavy+Light further processing TSE
Further processing
We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times.
Heavy gauge processing
| Processing type | Decoiling |
|---|---|
| Thickness range (mm) | 1.4 - 25.4 |
| Width range (mm) | 300 - 2600 |
| Length range | up to 18.4 m |
| Locations | Netherlands |
Light gauge processing
| Processing type | Slitting | Decoiling | Blanking |
|---|---|---|---|
| Thickness range (mm) | 0.2 - 7.0 | 0.3 - 6.0 | 0.3 - 6.0 |
| Width range (mm) | 10 - 2050 | 50 - 2600 | 200 - 2600 |
| Length range | - | up to 6 m | up to 6 m |
| Locations | Netherlands Germany France Spain Sweden Norway Finland |
Netherlands Germany France Spain Sweden Norway Finland |
Netherlands |
For further information please visit our Service Centre webpages.