Steel for gas cylinders
Tata Steel’s structural steel for gas cylinders offers excellent deep-drawing properties and weldability for ease of processing.
The grades allow for reliable normalising of the welded gas cylinder - retaining strength that contributes to optimal safety in use.
EN-Engineering-Product-Hot-Rolled-Gas cylinders-P245NB TSE
EN-Engineering-Product-Hot-Rolled-Gas cylinders-All grades Overview TSE
Relationship with standards
Steel for gas cylinders complies with the following European standard:
EN 10120: 2008 |
---|
Grade |
P245NB |
EN-EngineeringAutomotive-Product-Hot-rolled-All Grades Surface aspects Supply Conditions TSE
Supply - product conditions
Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:
Side/surface condition | non-pickled | pickled | pickled and oiled |
---|---|---|---|
Mill edges | Yes | Yes | Yes |
Trimmed edges | - | Yes | Yes |
Trimmed edges available in thicknesses up to 8.0 mm. The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs.
Surface aspects
Description | Availability |
---|---|
Surface finish | Coils are available in non-pickled and pickled finish |
Oiling | Pickled finish is available with rolling or preservative oil applied. Oil weight normally 0.5-2.5 g/m2 |
Alternative oiling ranges are available.
Please contact us for details.
EN-Engineering-Product-Hot-Rolled-Gas cylinders-P245NB-Properties TSE
Mechanical Properties
Steel for gas cylinders has the following mechanical properties, measured transverse to the rolling direction:
EN 10120: 2008 | Grade | P245NB |
---|---|---|
Min. yield strength1 ReH (N/mm²) | 245 | |
Tensile strength Rm (N/mm²) | 360 - 450 | |
Elongation % | ||
t < 3 | 26 | |
t ≥ 3 | 34 |
1. Upper yield strength or 0.2% proof stress applies.
Elongation after fracture A uses test piece length L0 = 80 mm for t < 3 and L0 = 5.65√S0 for t ≥ 3.
t – material thickness in mm.
Chemical composition
Tata Steel will satisfy the following cast analysis with values:
EN 10120: 2008 | Grade | P245NB |
---|---|---|
C | Max. | 0.16 |
Mn | Min. | 0.30 |
P | Max. | 0.025 |
S | Max. | 0.015 |
Si | Max. | 0.25 |
Altot | Min. | 0.020 |
N | Max. | 0.009 |
Nb | Max. | 0.050 |
Ti | Max. | 0.030 |
All values are in weight%.
Tata Steel does not use Cr, Cu, Mo or Ni as alloying elements for these steel grades.
EN-Engineering-Product-Hot-Rolled-Gas cylinders-P245NB-Dimensions TSE
Dimensional capability
Dimensions in mm.
Thickness | Max. width |
---|---|
From - up to | P245NB |
2.00 - 2.20 | 1700 |
2.20 - 2.40 | 1820 |
2.40 - 2.60 | 1920 |
2.60 - 2.70 | 2030 |
2.70 - 5.00 | 2070 |
The above capabilities apply to both pickled and non-pickled conditions.
The minimum width is 1000 mm.
Widths smaller than 1000 mm are available on request - please contact us.
Tolerances
Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010.
Tighter tolerances are available, please contact us.
EN-EngineeringAutomotive-Product-Hot-rolled-All grades Shape and dimensional tolerances TSE
Shape and dimensional tolerances
The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’).
The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.
If required, this part of the coil can be removed, however an additional cost may be charged for this.
Tolerances on thickness
Tata Steel can supply to full thickness tolerance specified in EN 10051:2010.
Tighter tolerances are available as shown below:
Product type | Thickness tolerances available | |||||
---|---|---|---|---|---|---|
(% of full EN 10051:2010 tolerance) | ||||||
100% | 75% | 66% | 60% | 50% | 33% | |
Steel for forming | Yes | Yes | Yes | Yes | Yes | Yes 1 |
High-strength low-alloy (HSLA EN 10149-2) | Yes | Yes | Yes | Yes | Yes | Yes 1 |
Ympress® HSLA | Yes | Yes 1 | ||||
Ympress® Laser | Yes | Yes 1 | ||||
Structural steel | Yes | Yes | Yes | Yes | Yes | Yes 1 |
Manganese boron steel | Yes | Yes | Yes | Yes | Yes | |
Case-hardening steel | Yes | Yes | Yes | Yes | Yes | |
High-carbon steel | Yes | |||||
Dual phase steel | Yes | |||||
Hot forming steel | Yes | |||||
Valast® abrasion resistant steel | Yes | Yes | Yes | Yes | Yes | |
Steel for pressure vessels | Yes | |||||
Steel for gas cylinders | Yes | |||||
Steel for line pipe | Yes | |||||
Ship plate | Yes |
1. Available for certain grades and thicknesses between 3.0 mm and 6.0 mm.
Please contact us on the availability of special tolerances to meet your requirements.
Tolerances on thickness for hot-rolled steel with a low carbon content
for cold forming (DD11-DD14 in EN 10111:2008)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.13 | ± 0.14 | ± 0.16 | - | |
> 2.00 | ≤ 2.50 | ± 0.14 | ± 0.16 | ± 0.17 | ± 0.19 |
> 2.50 | ≤ 3.00 | ± 0.15 | ± 0.17 | ± 0.18 | ± 0.20 |
> 3.00 | ≤ 4.00 | ± 0.17 | ± 0.18 | ± 0.20 | ± 0.20 |
> 4.00 | ≤ 5.00 | ± 0.18 | ± 0.20 | ± 0.21 | ± 0.22 |
> 5.00 | ≤ 6.00 | ± 0.20 | ± 0.21 | ± 0.22 | ± 0.23 |
> 6.00 | ≤ 8.00 | ± 0.22 | ± 0.23 | ± 0.23 | ± 0.26 |
> 8.00 | ≤ 11.00 | ± 0.24 | ± 0.25 | ± 0.25 | ± 0.28 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength Re ≤ 300 N/mm2 (category A)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.17 | ± 0.19 | ± 0.21 | - | |
> 2.00 | ≤ 2.50 | ± 0.18 | ± 0.21 | ± 0.23 | ± 0.25 |
> 2.50 | ≤ 3.00 | ± 0.20 | ± 0.22 | ± 0.24 | ± 0.26 |
> 3.00 | ≤ 4.00 | ± 0.22 | ± 0.24 | ± 0.26 | ± 0.27 |
> 4.00 | ≤ 5.00 | ± 0.24 | ± 0.26 | ± 0.28 | ± 0.29 |
> 5.00 | ≤ 6.00 | ± 0.26 | ± 0.28 | ± 0.29 | ± 0.31 |
> 6.00 | ≤ 8.00 | ± 0.29 | ± 0.30 | ± 0.31 | ± 0.35 |
> 8.00 | ≤ 10.00 | ± 0.32 | ± 0.33 | ± 0.34 | ± 0.40 |
> 10.00 | ≤ 12.50 | ± 0.35 | ± 0.36 | ± 0.37 | ± 0.43 |
> 12.50 | ≤ 15.00 | ± 0.37 | ± 0.38 | ± 0.40 | ± 0.46 |
> 15.00 | ≤ 25.00 | ± 0.40 | ± 0.42 | ± 0.45 | ± 0.50 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength 300 N/mm2 < Re ≤ 360 N/mm2 (category B)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.20 | ± 0.22 | ± 0.24 | - | |
> 2.00 | ≤ 2.50 | ± 0.21 | ± 0.24 | ± 0.26 | ± 0.29 |
> 2.50 | ≤ 3.00 | ± 0.23 | ± 0.25 | ± 0.28 | ± 0.30 |
> 3.00 | ≤ 4.00 | ± 0.25 | ± 0.28 | ± 0.30 | ± 0.31 |
> 4.00 | ≤ 5.00 | ± 0.28 | ± 0.30 | ± 0.32 | ± 0.33 |
> 5.00 | ≤ 6.00 | ± 0.30 | ± 0.32 | ± 0.33 | ± 0.36 |
> 6.00 | ≤ 8.00 | ± 0.33 | ± 0.35 | ± 0.36 | ± 0.40 |
> 8.00 | ≤ 10.00 | ± 0.37 | ± 0.38 | ± 0.39 | ± 0.46 |
> 10.00 | ≤ 12.50 | ± 0.40 | ± 0.41 | ± 0.43 | ± 0.49 |
> 12.50 | ≤ 15.00 | ± 0.43 | ± 0.44 | ± 0.46 | ± 0.53 |
> 15.00 | ≤ 25.00 | ± 0.46 | ± 0.48 | ± 0.52 | ± 0.58 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength 360 N/mm2 < Re ≤ 420 N/mm2 (category C)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.22 | ± 0.25 | ± 0.27 | - | |
> 2.00 | ≤ 2.50 | ± 0.23 | ± 0.27 | ± 0.30 | ± 0.33 |
> 2.50 | ≤ 3.00 | ± 0.26 | ± 0.29 | ± 0.31 | ± 0.34 |
> 3.00 | ≤ 4.00 | ± 0.29 | ± 0.31 | ± 0.34 | ± 0.35 |
> 4.00 | ≤ 5.00 | ± 0.31 | ± 0.34 | ± 0.36 | ± 0.38 |
> 5.00 | ≤ 6.00 | ± 0.34 | ± 0.36 | ± 0.38 | ± 0.40 |
> 6.00 | ≤ 8.00 | ± 0.38 | ± 0.39 | ± 0.40 | ± 0.46 |
> 8.00 | ≤ 10.00 | ± 0.42 | ± 0.43 | ± 0.44 | ± 0.52 |
> 10.00 | ≤ 12.50 | ± 0.46 | ± 0.47 | ± 0.48 | ± 0.56 |
> 12.50 | ≤ 15.00 | ± 0.48 | ± 0.49 | ± 0.52 | ± 0.60 |
> 15.00 | ≤ 25.00 | ± 0.52 | ± 0.55 | ± 0.59 | ± 0.65 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength 420 N/mm2 < Re ≤ 900 N/mm2 (category D)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.24 | ± 0.27 | ± 0.29 | - | |
> 2.00 | ≤ 2.50 | ± 0.25 | ± 0.29 | ± 0.32 | ± 0.35 |
> 2.50 | ≤ 3.00 | ± 0.28 | ± 0.31 | ± 0.34 | ± 0.36 |
> 3.00 | ≤ 4.00 | ± 0.31 | ± 0.34 | ± 0.36 | ± 0.38 |
> 4.00 | ≤ 5.00 | ± 0.34 | ± 0.36 | ± 0.39 | ± 0.41 |
> 5.00 | ≤ 6.00 | ± 0.36 | ± 0.39 | ± 0.41 | ± 0.43 |
> 6.00 | ≤ 8.00 | ± 0.41 | ± 0.42 | ± 0.43 | ± 0.49 |
> 8.00 | ≤ 10.00 | ± 0.45 | ± 0.46 | ± 0.48 | ± 0.56 |
> 10.00 | ≤ 12.50 | ± 0.49 | ± 0.50 | ± 0.52 | ± 0.60 |
> 12.50 | ≤ 15.00 | ± 0.52 | ± 0.53 | ± 0.56 | ± 0.64 |
> 15.00 | ≤ 25.00 | ± 0.56 | ± 0.59 | ± 0.63 | ± 0.70 |
All dimensions are mm.
Tolerances on width
Tolerances in mm.
Nominal width w | ||||
---|---|---|---|---|
Mill edges | Trimmed edges | |||
lower | upper | lower | upper | |
w ≤ 1200 | 0 | 20 | 0 | 3 |
1200 < w ≤ 1850 | 0 | 20 | 0 | 5 |
w > 1850 | 0 | 25 | 0 | 6 |
Tolerances in mm for wide strip and slit wide strip
The tolerances for wide strip and slit wide strip comply with standard EN 10051:2010.
The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’).
The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.
If required, this part of the coil can be removed, however an additional cost may be charged for this.
Edge camber
The deviation from the edge over a length of 5000 mm:
• with mill edges, no more than 20 mm
• with trimmed edges, no more than 15 mm
Flatness
Requirements as regards flatness can be agreed at the time of enquiry.
Option for maximum crown values
The following high crown C40 options available for hot-rolled products.
Crown values on the C20-position as well as minimum crown values
on both C20 and C40 position are also available on request.
Maximum Crown C40 in µm values for hot-rolled steel
with a low carbon content for cold forming (DD11-DD14 in EN 10111:2008)
Category 1 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 40 | 40 | 40 | 40 |
> 2.00 | ≤ 2.50 | 40 | 40 | 50 | 50 |
> 2.50 | ≤ 3.00 | 40 | 40 | 50 | 50 |
> 3.00 | ≤ 6.00 | 40 | 50 | 50 | 50 |
> 6.00 | ≤ 11.00 | 50 | 50 | 50 | 50 |
Maximum Crown C40 in µm values of structural steel grades
(S185-S235-S275 ≤ 10mm in EN 10025-2:2004)
Category 2 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 40 | 40 | 40 | 40 |
> 2.00 | ≤ 2.50 | 40 | 40 | 50 | 50 |
> 2.50 | ≤ 20.00 | 50 | 50 | 50 | 50 |
Maximum Crown C40 in µm values of structural steel grades
(S275 > 10mm in EN 10025-2:2004) and HSLA grades (S315MC in EN 10149-2:1996)
Category 3 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 50 | 50 | 60 | 60 |
> 2.00 | ≤ 2.50 | 50 | 60 | 60 | 60 |
> 2.50 | ≤ 3.00 | 50 | 60 | 60 | 60 |
> 3.00 | ≤ 20.00 | 60 | 60 | 70 | 70 |
Maximum Crown C40 in µm values of HSLA grades
(S355MC, S420MC, S460MC, S500MC, S550MC in EN 10149-2:1996)
Category 4 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 60 | 70 | 70 | 70 |
> 2.00 | ≤ 2.50 | 60 | 70 | 80 | 80 |
> 2.50 | ≤ 3.00 | 60 | 70 | 80 | 80 |
> 3.00 | ≤ 5.00 | 70 | 70 | 80 | 80 |
> 5.00 | ≤ 20.00 | 80 | 80 | 80 | 80 |
Dimensions and coil weights
Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights:
Description | Availability |
---|---|
Coil diameter inner non-pickled | 762 mm |
Coil diameter inner pickled | 610 mm standard |
762 mm on request | |
Tolerance on inner diameter | +0/-50 mm |
Coil diameter outer non-pickled | Outer diameter available is 10/7 x width |
to reduce possibility of coil tipping over | |
Max. 2300 mm | |
Min. 1200 mm | |
Coil diameter outer pickled and oiled | Outer diameter available is 10/7 x width |
to reduce possibility of coil tipping over | |
Outer diameter | |
limit 2200 mm | |
Min. 1050 mm | |
Coil weight | Max. 38,5 tonnes |
Additional maximum limits from transport | |
limits and outer coil diameter | |
Some HR products may have different | |
coil weight ranges | |
KIM*: width ≤ 1200 mm | max. 23.1 kg/mm width |
KIM*: 1200 < width ≤ 1700 mm | max. 21.6 kg/mm width |
KIM*: 1700 < width ≤ 1900 mm | max. 20.9 kg/mm width |
KIM*: width > 1900 mm | max. 18.8 kg/mm width |
Minimum tonnage per order | Please refer to price list for order quantity details |
Minimum order quantities may apply |
* Other KIM values may be available - please contact us.
EN-EngineeringAutomotive-Product-Hot-rolled-Heavy+Light further processing TSE
Further processing
We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times.
Heavy gauge processing
Processing type | Decoiling |
---|---|
Thickness range (mm) | 1.4 - 25.4 |
Width range (mm) | 300 - 2600 |
Length range | up to 18.4 m |
Locations | Netherlands |
Light gauge processing
Processing type | Slitting | Decoiling | Blanking |
---|---|---|---|
Thickness range (mm) | 0.2 - 7.0 | 0.3 - 6.0 | 0.3 - 6.0 |
Width range (mm) | 10 - 2050 | 50 - 2600 | 200 - 2600 |
Length range | - | up to 6 m | up to 6 m |
Locations | Netherlands Germany France Spain Sweden Norway Finland |
Netherlands Germany France Spain Sweden Norway Finland |
Netherlands |
For further information please visit our Service Centre webpages.
EN-Engineering-Product-Hot-Rolled-Gas cylinders-P265N TSE
EN-Engineering-Product-Hot-Rolled-Gas cylinders-All grades Overview TSE
Relationship with standards
Steel for gas cylinders complies with the following European standard:
EN 10120: 2008 |
---|
Grade |
P245NB |
EN-EngineeringAutomotive-Product-Hot-rolled-All Grades Surface aspects Supply Conditions TSE
Supply - product conditions
Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:
Side/surface condition | non-pickled | pickled | pickled and oiled |
---|---|---|---|
Mill edges | Yes | Yes | Yes |
Trimmed edges | - | Yes | Yes |
Trimmed edges available in thicknesses up to 8.0 mm. The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs.
Surface aspects
Description | Availability |
---|---|
Surface finish | Coils are available in non-pickled and pickled finish |
Oiling | Pickled finish is available with rolling or preservative oil applied. Oil weight normally 0.5-2.5 g/m2 |
Alternative oiling ranges are available.
Please contact us for details.
EN-Engineering-Product-Hot-Rolled-Gas cylinders-P265NB-Properties TSE delete
Mechanical Properties
Steel for gas cylinders has the following mechanical properties, measured transverse to the rolling direction:
EN 10120: 2008 | Grade | P265NB |
---|---|---|
Elongation % | ||
Min. yield strength1 ReH (N/mm²) | 265 | |
Tensile strength Rm (N/mm²) | 410 - 500 | |
t < 3 | 24 | |
t ≥ 3 | 32 |
1. Upper yield strength or 0.2% proof stress applies.
Elongation after fracture A uses test piece length L0 = 80 mm for t < 3 and L0 = 5.65√S0 for t ≥ 3.
t – material thickness in mm.
Chemical composition
Tata Steel will satisfy the following cast analysis:
EN 10120: 2008 | Grade | P265NB |
---|---|---|
C | Max. | 0.19 |
Mn | Min. | 0.40 |
P | Max. | 0.025 |
S | Max. | 0.015 |
Si | Max. | 0.25 |
Altot | Min. | 0.020 |
N | Max. | 0.009 |
Nb | Max. | 0.050 |
Ti | Max. | 0.030 |
All values are in weight%.
Tata Steel does not use Cr, Cu, Mo or Ni as alloying elements for these steel grades.
EN-Engineering-Product-Hot-Rolled-Gas cylinders-P265NB-Dimensions TSE delete
Dimensional capability
Dimensions in mm.
Thickness | Max. width |
---|---|
From - up to | P265NB |
2.00 - 2.20 | 1700 |
2.20 - 2.40 | 1820 |
2.40 - 2.60 | 1920 |
2.60 - 2.70 | 2030 |
2.70 - 5.00 | 2070 |
The above capabilities apply to both pickled and non-pickled conditions.
The minimum width is 1000 mm.
Widths smaller than 1000 mm are available on request - please contact us.
Tolerances
Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010.
Tighter tolerances are available, please contact us.
EN-EngineeringAutomotive-Product-Hot-rolled-All grades Shape and dimensional tolerances TSE
Shape and dimensional tolerances
The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’).
The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.
If required, this part of the coil can be removed, however an additional cost may be charged for this.
Tolerances on thickness
Tata Steel can supply to full thickness tolerance specified in EN 10051:2010.
Tighter tolerances are available as shown below:
Product type | Thickness tolerances available | |||||
---|---|---|---|---|---|---|
(% of full EN 10051:2010 tolerance) | ||||||
100% | 75% | 66% | 60% | 50% | 33% | |
Steel for forming | Yes | Yes | Yes | Yes | Yes | Yes 1 |
High-strength low-alloy (HSLA EN 10149-2) | Yes | Yes | Yes | Yes | Yes | Yes 1 |
Ympress® HSLA | Yes | Yes 1 | ||||
Ympress® Laser | Yes | Yes 1 | ||||
Structural steel | Yes | Yes | Yes | Yes | Yes | Yes 1 |
Manganese boron steel | Yes | Yes | Yes | Yes | Yes | |
Case-hardening steel | Yes | Yes | Yes | Yes | Yes | |
High-carbon steel | Yes | |||||
Dual phase steel | Yes | |||||
Hot forming steel | Yes | |||||
Valast® abrasion resistant steel | Yes | Yes | Yes | Yes | Yes | |
Steel for pressure vessels | Yes | |||||
Steel for gas cylinders | Yes | |||||
Steel for line pipe | Yes | |||||
Ship plate | Yes |
1. Available for certain grades and thicknesses between 3.0 mm and 6.0 mm.
Please contact us on the availability of special tolerances to meet your requirements.
Tolerances on thickness for hot-rolled steel with a low carbon content
for cold forming (DD11-DD14 in EN 10111:2008)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.13 | ± 0.14 | ± 0.16 | - | |
> 2.00 | ≤ 2.50 | ± 0.14 | ± 0.16 | ± 0.17 | ± 0.19 |
> 2.50 | ≤ 3.00 | ± 0.15 | ± 0.17 | ± 0.18 | ± 0.20 |
> 3.00 | ≤ 4.00 | ± 0.17 | ± 0.18 | ± 0.20 | ± 0.20 |
> 4.00 | ≤ 5.00 | ± 0.18 | ± 0.20 | ± 0.21 | ± 0.22 |
> 5.00 | ≤ 6.00 | ± 0.20 | ± 0.21 | ± 0.22 | ± 0.23 |
> 6.00 | ≤ 8.00 | ± 0.22 | ± 0.23 | ± 0.23 | ± 0.26 |
> 8.00 | ≤ 11.00 | ± 0.24 | ± 0.25 | ± 0.25 | ± 0.28 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength Re ≤ 300 N/mm2 (category A)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.17 | ± 0.19 | ± 0.21 | - | |
> 2.00 | ≤ 2.50 | ± 0.18 | ± 0.21 | ± 0.23 | ± 0.25 |
> 2.50 | ≤ 3.00 | ± 0.20 | ± 0.22 | ± 0.24 | ± 0.26 |
> 3.00 | ≤ 4.00 | ± 0.22 | ± 0.24 | ± 0.26 | ± 0.27 |
> 4.00 | ≤ 5.00 | ± 0.24 | ± 0.26 | ± 0.28 | ± 0.29 |
> 5.00 | ≤ 6.00 | ± 0.26 | ± 0.28 | ± 0.29 | ± 0.31 |
> 6.00 | ≤ 8.00 | ± 0.29 | ± 0.30 | ± 0.31 | ± 0.35 |
> 8.00 | ≤ 10.00 | ± 0.32 | ± 0.33 | ± 0.34 | ± 0.40 |
> 10.00 | ≤ 12.50 | ± 0.35 | ± 0.36 | ± 0.37 | ± 0.43 |
> 12.50 | ≤ 15.00 | ± 0.37 | ± 0.38 | ± 0.40 | ± 0.46 |
> 15.00 | ≤ 25.00 | ± 0.40 | ± 0.42 | ± 0.45 | ± 0.50 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength 300 N/mm2 < Re ≤ 360 N/mm2 (category B)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.20 | ± 0.22 | ± 0.24 | - | |
> 2.00 | ≤ 2.50 | ± 0.21 | ± 0.24 | ± 0.26 | ± 0.29 |
> 2.50 | ≤ 3.00 | ± 0.23 | ± 0.25 | ± 0.28 | ± 0.30 |
> 3.00 | ≤ 4.00 | ± 0.25 | ± 0.28 | ± 0.30 | ± 0.31 |
> 4.00 | ≤ 5.00 | ± 0.28 | ± 0.30 | ± 0.32 | ± 0.33 |
> 5.00 | ≤ 6.00 | ± 0.30 | ± 0.32 | ± 0.33 | ± 0.36 |
> 6.00 | ≤ 8.00 | ± 0.33 | ± 0.35 | ± 0.36 | ± 0.40 |
> 8.00 | ≤ 10.00 | ± 0.37 | ± 0.38 | ± 0.39 | ± 0.46 |
> 10.00 | ≤ 12.50 | ± 0.40 | ± 0.41 | ± 0.43 | ± 0.49 |
> 12.50 | ≤ 15.00 | ± 0.43 | ± 0.44 | ± 0.46 | ± 0.53 |
> 15.00 | ≤ 25.00 | ± 0.46 | ± 0.48 | ± 0.52 | ± 0.58 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength 360 N/mm2 < Re ≤ 420 N/mm2 (category C)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.22 | ± 0.25 | ± 0.27 | - | |
> 2.00 | ≤ 2.50 | ± 0.23 | ± 0.27 | ± 0.30 | ± 0.33 |
> 2.50 | ≤ 3.00 | ± 0.26 | ± 0.29 | ± 0.31 | ± 0.34 |
> 3.00 | ≤ 4.00 | ± 0.29 | ± 0.31 | ± 0.34 | ± 0.35 |
> 4.00 | ≤ 5.00 | ± 0.31 | ± 0.34 | ± 0.36 | ± 0.38 |
> 5.00 | ≤ 6.00 | ± 0.34 | ± 0.36 | ± 0.38 | ± 0.40 |
> 6.00 | ≤ 8.00 | ± 0.38 | ± 0.39 | ± 0.40 | ± 0.46 |
> 8.00 | ≤ 10.00 | ± 0.42 | ± 0.43 | ± 0.44 | ± 0.52 |
> 10.00 | ≤ 12.50 | ± 0.46 | ± 0.47 | ± 0.48 | ± 0.56 |
> 12.50 | ≤ 15.00 | ± 0.48 | ± 0.49 | ± 0.52 | ± 0.60 |
> 15.00 | ≤ 25.00 | ± 0.52 | ± 0.55 | ± 0.59 | ± 0.65 |
All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum
yield strength 420 N/mm2 < Re ≤ 900 N/mm2 (category D)
Nominal thickness | Tolerances for a nominal width of | ||||
---|---|---|---|---|---|
≤ 1200 | > 1200 | > 1500 | > 1800 | ||
≤ 1500 | ≤ 1800 | ||||
≤ 2.00 | ± 0.24 | ± 0.27 | ± 0.29 | - | |
> 2.00 | ≤ 2.50 | ± 0.25 | ± 0.29 | ± 0.32 | ± 0.35 |
> 2.50 | ≤ 3.00 | ± 0.28 | ± 0.31 | ± 0.34 | ± 0.36 |
> 3.00 | ≤ 4.00 | ± 0.31 | ± 0.34 | ± 0.36 | ± 0.38 |
> 4.00 | ≤ 5.00 | ± 0.34 | ± 0.36 | ± 0.39 | ± 0.41 |
> 5.00 | ≤ 6.00 | ± 0.36 | ± 0.39 | ± 0.41 | ± 0.43 |
> 6.00 | ≤ 8.00 | ± 0.41 | ± 0.42 | ± 0.43 | ± 0.49 |
> 8.00 | ≤ 10.00 | ± 0.45 | ± 0.46 | ± 0.48 | ± 0.56 |
> 10.00 | ≤ 12.50 | ± 0.49 | ± 0.50 | ± 0.52 | ± 0.60 |
> 12.50 | ≤ 15.00 | ± 0.52 | ± 0.53 | ± 0.56 | ± 0.64 |
> 15.00 | ≤ 25.00 | ± 0.56 | ± 0.59 | ± 0.63 | ± 0.70 |
All dimensions are mm.
Tolerances on width
Tolerances in mm.
Nominal width w | ||||
---|---|---|---|---|
Mill edges | Trimmed edges | |||
lower | upper | lower | upper | |
w ≤ 1200 | 0 | 20 | 0 | 3 |
1200 < w ≤ 1850 | 0 | 20 | 0 | 5 |
w > 1850 | 0 | 25 | 0 | 6 |
Tolerances in mm for wide strip and slit wide strip
The tolerances for wide strip and slit wide strip comply with standard EN 10051:2010.
The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’).
The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.
If required, this part of the coil can be removed, however an additional cost may be charged for this.
Edge camber
The deviation from the edge over a length of 5000 mm:
• with mill edges, no more than 20 mm
• with trimmed edges, no more than 15 mm
Flatness
Requirements as regards flatness can be agreed at the time of enquiry.
Option for maximum crown values
The following high crown C40 options available for hot-rolled products.
Crown values on the C20-position as well as minimum crown values
on both C20 and C40 position are also available on request.
Maximum Crown C40 in µm values for hot-rolled steel
with a low carbon content for cold forming (DD11-DD14 in EN 10111:2008)
Category 1 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 40 | 40 | 40 | 40 |
> 2.00 | ≤ 2.50 | 40 | 40 | 50 | 50 |
> 2.50 | ≤ 3.00 | 40 | 40 | 50 | 50 |
> 3.00 | ≤ 6.00 | 40 | 50 | 50 | 50 |
> 6.00 | ≤ 11.00 | 50 | 50 | 50 | 50 |
Maximum Crown C40 in µm values of structural steel grades
(S185-S235-S275 ≤ 10mm in EN 10025-2:2004)
Category 2 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 40 | 40 | 40 | 40 |
> 2.00 | ≤ 2.50 | 40 | 40 | 50 | 50 |
> 2.50 | ≤ 20.00 | 50 | 50 | 50 | 50 |
Maximum Crown C40 in µm values of structural steel grades
(S275 > 10mm in EN 10025-2:2004) and HSLA grades (S315MC in EN 10149-2:1996)
Category 3 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 50 | 50 | 60 | 60 |
> 2.00 | ≤ 2.50 | 50 | 60 | 60 | 60 |
> 2.50 | ≤ 3.00 | 50 | 60 | 60 | 60 |
> 3.00 | ≤ 20.00 | 60 | 60 | 70 | 70 |
Maximum Crown C40 in µm values of HSLA grades
(S355MC, S420MC, S460MC, S500MC, S550MC in EN 10149-2:1996)
Category 4 | C40 | ||||
---|---|---|---|---|---|
Nominal Thickness | ≤ 1200 | > 1200 | > 1500 | > 1800 | |
≤ 1500 | ≤ 1800 | ||||
> 1.47 | ≤ 2.00 | 60 | 70 | 70 | 70 |
> 2.00 | ≤ 2.50 | 60 | 70 | 80 | 80 |
> 2.50 | ≤ 3.00 | 60 | 70 | 80 | 80 |
> 3.00 | ≤ 5.00 | 70 | 70 | 80 | 80 |
> 5.00 | ≤ 20.00 | 80 | 80 | 80 | 80 |
Dimensions and coil weights
Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights:
Description | Availability |
---|---|
Coil diameter inner non-pickled | 762 mm |
Coil diameter inner pickled | 610 mm standard |
762 mm on request | |
Tolerance on inner diameter | +0/-50 mm |
Coil diameter outer non-pickled | Outer diameter available is 10/7 x width |
to reduce possibility of coil tipping over | |
Max. 2300 mm | |
Min. 1200 mm | |
Coil diameter outer pickled and oiled | Outer diameter available is 10/7 x width |
to reduce possibility of coil tipping over | |
Outer diameter | |
limit 2200 mm | |
Min. 1050 mm | |
Coil weight | Max. 38,5 tonnes |
Additional maximum limits from transport | |
limits and outer coil diameter | |
Some HR products may have different | |
coil weight ranges | |
KIM*: width ≤ 1200 mm | max. 23.1 kg/mm width |
KIM*: 1200 < width ≤ 1700 mm | max. 21.6 kg/mm width |
KIM*: 1700 < width ≤ 1900 mm | max. 20.9 kg/mm width |
KIM*: width > 1900 mm | max. 18.8 kg/mm width |
Minimum tonnage per order | Please refer to price list for order quantity details |
Minimum order quantities may apply |
* Other KIM values may be available - please contact us.
EN-EngineeringAutomotive-Product-Hot-rolled-Heavy+Light further processing TSE
Further processing
We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times.
Heavy gauge processing
Processing type | Decoiling |
---|---|
Thickness range (mm) | 1.4 - 25.4 |
Width range (mm) | 300 - 2600 |
Length range | up to 18.4 m |
Locations | Netherlands |
Light gauge processing
Processing type | Slitting | Decoiling | Blanking |
---|---|---|---|
Thickness range (mm) | 0.2 - 7.0 | 0.3 - 6.0 | 0.3 - 6.0 |
Width range (mm) | 10 - 2050 | 50 - 2600 | 200 - 2600 |
Length range | - | up to 6 m | up to 6 m |
Locations | Netherlands Germany France Spain Sweden Norway Finland |
Netherlands Germany France Spain Sweden Norway Finland |
Netherlands |
For further information please visit our Service Centre webpages.